Material Safety Data Sheet

1. Chemical Product and Company Identification

 APPLICATION: E-617; 55100

         Manufacturer/Supplier Information

 MSDS Prepared by:
 Elmer's Products, Inc. Emergency Phone Number
 1 Easton Oval Poison Control Center
 Columbus, OH 43219 888-516-2502
 For additional health, safety or regulatory information, call 888-435-6377.
 Call 1-800-848-9400 to place an order or request additional MSDSs.

2. Composition, Information on Ingredients

 The ingredients listed below have been associated with one or more
 immediate and/or delayed(*) health hazards. Risk of damage and effects
 depends upon duration and level of exposure. BEFORE USING, HANDLING, OR
 % by weight
 7085-85-0 Ethyl 2-Cyanoacrylate 
69012-64-2 Fumed, Silica 

3. Hazards Identification


3.1 Emergency Overview

 Appearance Colorless gel
 Odor Irritating
 May become unstable at high temperatures or may react with water.
 May be harmful if inhaled. May cause irritation of nose, throat and
 Bonds skin instantly. Causes skin irritation.
 Bonds eyelids instantly. Causes eye irritation.

         HMIS Rating

 HEALTH = 2 (moderate)
 FLAMMABILITY = 2 (moderate)
 REACTIVITY = 1 (slight)

3.2 Potential Health Effects


         Immediate Hazards

 INGESTION: No hazards known to company.
 INHALATION: May be harmful if inhaled. Vapor may cause irritation
 of nose, throat and lungs.
 SKIN: Bonds skin instantly. Causes irritation.
 EYES: Bonds eyelids instantly. Causes irritation.

         Delayed Hazards

 None of the components present in this product at concentrations equal
 to or greater than 0.1% have been listed by NTP, classified by IARC,
 nor regulated by OSHA as a carcinogen.

4. First Aid Measures

 INGESTION: If accidentally swallowed, dilute by drinking large
 quantities of water. Immediately contact poison control
 center or hospital emergency room for any other
 additional treatment directions.
 INHALATION: If inhaled, remove to fresh air. If not breathing,
 give artificial respiration, preferably mouth-to-mouth.
 Call a physician.
 SKIN: If skin bonding occurs, soak in nail polish remover
 or acetone and carefully peel or roll skin apart (do not
 EYES: If eye contact occurs, hold eyelid open and rinse
 thoroughly but gently with only water for 15 minutes and
 GET MEDICAL ATTENTION. Do not use any solvents to
 flush the eye and its surroundings. Liquid glue will
 sting eye temporarily. Solidified glue may irritate eye
 like a grain of sand and should be treated by an eye

5. Fire Fighting Measures

 Autoignition Temperature 485 deg C
 Upper/Lower Flammable Limits Not available
 Up/Lower Explosive Limits, % by Vol Not available
 Flash Point 83 deg C (CC)
 Keep away from heat and flame.
 In case of fire, use water spray, dry chemical, foam or CO2. Use
 water to keep fire-exposed containers cool.

6. Accidental Release Measures

 Eliminate all ignition sources. Sweep (scoop) up and remove to a
 chemical disposal area. Prevent entry into natural bodies of water.

7. Handling and Storage


7.1 Handling

 Handle in accordance with good industrial hygiene and safety
 practices. These practices include avoiding unnecessary exposure and
 removal of the material from eyes, skin and clothing.
 Wash thoroughly after handling. Always use appropriate Personal
 Protective Equipment (PPE).
 INHALATION: Avoid breathing vapor. Use with adequate
 SKIN: Avoid contact with skin and clothing.
 EYES: Avoid contact with eyes.

7.2 Storage

 Keep away from amines.
 Store in cool, dry area away from sun and heat.
 Keep containers tightly closed.
 Exposure to small amounts of moisture, even moisture in air, causes
 polymerization and renders the product unusable.
 Keep away from heat, sparks, flame and other ignition sources.

8. Exposure Controls/Personal Protection


8.1 Exposure Controls

 ENGINEERING CONTROLS: The following exposure control techniques may
 be used to effectively minimize employee exposure: local exhaust
 ventilation, enclosed system design, process isolation and remote
 control in combination with appropriate use of personal protective
 equipment and prudent work practices. These techniques may not
 necessarily address all issues pertaining to your operations. We,
 therefore, recommend that you consult with experts of your choice to
 determine whether or not your programs are adequate.
 If airborne contaminants are generated when the material is heated or
 handled, sufficient ventilation in volume and air flow patterns should
 be provided to keep air contaminant concentration levels below
 acceptable criteria.

8.2 Personal Protection

 Where air contaminants can exceed acceptable criteria, use NIOSH/MSHA
 approved respiratory protection equipment. Respirators should be
 selected based on the form and concentration of contaminants in air
 in accordance with OSHA laws and regulations or other applicable
 standards or guidelines, including ANSI standards regarding
 respiratory protection. Use goggles if contact is likely. Wear
 impervious gloves as required to prevent skin contact.

8.3 Exposure Guidelines

 Ethyl 2-Cyanoacrylate 7085-85-0 
ACGIH TLV: 0.2 ppm (1 mg/m) TWA
 Fumed, Silica 69012-64-2 
ACGIH TLV: 2 mg/m TWA, respirable fraction
 OSHA PEL: 20 mppcf; 80/(%SiO2) mg/m TWA
 REMANDED PEL: 6 mg/m TWA (as Silica)
 OSHA 1989 PEL remanded, but in effect in some states

9. Physical and Chemical Properties

 Percent Volatiles Not determined
 pH @ 25 C Not available
 Specific Gravity 1.09
 Appearance Colorless gel
 Autoignition Temperature 485 deg C
 Boiling Point 62 deg C (5 mm Hg)
 Vapor Density (Air=1) > 1
 Vapor Pressure, mm Hg @ 20 C 0.13
 Evaporation Rate (Butyl Acetate=1) < 1
 Upper/Lower Flammable Limits Not available
 Up/Lower Explosive Limits, % by Vol Not available
 Flash Point 83 deg C (CC)
 Freezing Point < -20 deg C
 Odor Irritating
 Odor Threshold, ppm Not available
 Solubility in Water Negligible
 Coefficient of Water/Oil Distrib. Not applicable

10. Stability and Reactivity

 Normally stable, but may become unstable at high temperatures or may
 react with water.

         Conditions to Avoid:

 Exposure to heat, flame and incompatibles.


 Water, alcohols, amines, bases and direct UV.

         Decomposition products may include:

 Oxides of carbon.

         Hazardous polymerization:

 Will not occur.

         Other Hazards:

 None known to company.

11. Toxicological Information

 See Section 3 Hazards Identification information.
 Ethyl 2-Cyanoacrylate 7085-85-0 
LC50: Not available
 LD50: Not available
 Fumed, Silica 69012-64-2 
LC50: Not available
 LD50: Not available

12. Ecological Information

 Not determined.

13. Disposal Considerations

 Dispose of according to local, state/provincial, and federal
 Empty container: May contain explosive vapors. DO NOT cut, puncture
 or weld on or nearby.

14. Transport Information


14.1 U.S. Department of Transportation (DOT)

 The data provided in this section is for information only and may not
 be specific to your package size. You will need to apply the
 appropriate regulations to properly classify your shipment for

14.2 Canadian Transportation of Dangerous Goods (TDG)


15. Regulatory Information (Selected Regulations)


15.1 U.S. Federal Regulations


         OSHA Hazard Communication Standard 29CFR1910.1200

 This material is a "health hazard" and/or a "physical hazard" as
 determined when reviewed according to the requirements of the
 Occupational Safety and Health Administration 29 CFR Part 1910.1200
 "Hazard Communication" Standard.

         SARA Title III: Section 311/312

 Fire hazard
 Immediate health hazard

         SARA Title III Section 313 and 40 CFR Part 372

 This product contains the following toxic chemical(s) subject to the
 reporting requirements of Section 313 of Title III of the Superfund
 Amendments and Reauthorization Act of 1986, and Subpart C-Supplier
 Notification Requirement of 40 CFR Part 372.
 None required per SARA TITLE III SECTION 313.

         TSCA Section 8(b) Inventory

 All reportable chemical substances are listed on the TSCA Inventory.
 We rely on certifications of compliance from our suppliers for
 chemical substances not manufactured by us.

15.2 Canadian Regulations


         Workplace Hazardous Materials Information System (WHMIS)

 This product has been classified in accordance with the hazard
 criteria of the Controlled Products Regulation (CPR) and the MSDS
 contains all the information required by the CPR.

         Canadian Environmental Protection Act (CEPA)

 All reportable chemical substances are listed on the Domestic
 Substances List (DSL) or otherwise comply with CEPA new substance
 notification requirements.

         National Pollutant Release Inventory (NPRI)

 This product contains the following chemical(s) subject to the
 reporting requirements of the Canadian Environmental Protection Act
 (CEPA) subsection 16(1), National Pollutant Release Inventory.
 None required.

16. Other Information

 HL (Cautions Required): Products bearing the HL Health Label
 (Cautions Required) Seal of The Art & Creative Materials Institute,
 Inc. (ACMI) are certified to be properly labeled in a program of
 toxicological evaluation by a medical expert. This program is
 reviewed by ACMI's Toxicological Advisory Board. These products are
 certified by ACMI to be labeled in accordance with the chronic hazard
 labeling standard, ASTM D-4236 and Federal Law, P.L. 100-695.

         User's Responsibility

 The OSHA Hazard Communication Standard 29CFR 1910.1200 and the Workplace
 Hazardous Materials Information System (WHMIS) require that the information
 contained on these sheets be made available to your workers. Educate and
 train your workers regarding OSHA and WHMIS precautions. Instruct your
 workers to handle this product properly. Consult with appropriate experts
 to guard against hazards associated with use of this product and its


 shall conform to contracted specifications, and that the product does not
 infringe any valid United States or Canadian patent. No claim of any kind
 shall be greater in amount than the purchase price of the quantity of
 product in respect of which damages are claimed. In no event shall Seller
 be liable for incidental or consequential damages, whether Buyer's claim is
 based on contract, breach of warranty, negligence or otherwise.